Clean and Oil
Stripping gun, cleaning all parts, checking for wear, making suggestions to a customer of services needed to put in A-1 condition.
-
Handgun $65
-
Rifle & AR/AK Pistol $130
Sonic Cleaning
-
Handgun $95
-
Rifle & AR/AK Pistol $160
Rebluing
-
Abrasive / Media Blast / Wire Wheel (Matte Finish) $250
-
Hangun Deluxe Finish $300
Same as above followed with #240 and $400 grit polish with all screw holes and corners protected and square
-
Rifle & AR/AK Pistol $400
Same as above followed with #240 and $400 grit polish with all screw holes and corners protected and square
-
Slow Rust Bluing $250-$650
-
Cerakote $200
-
Bead, Sandblast or Wire Brush Stainless Steel $140
Sight Work
-
Sight In Customer Gun $75
Does not include cost of ammo, targets, etc.
-
Bore Sight Customer Gun $25
-
Pattern Shotgun $25
Does not include cost of ammo, targets, etc.
-
Install Insert In Pistol Sight $50
-
Install Front / Mid-Rib Shotgun Bead $65
-
Install Receiver Sights $45
Gun Drilled and Tapped
-
Scope Mounting $50
Gun Drilled and Tapped
General Barrel, Action & Rifle Work
-
Check Headspace $65
-
Remove Stuck Fired Case From Chamber $50
-
Remove Live Round From Chamber $130
-
Remove Obstruction From Bore Hourly Rate
-
Remove Fouling From Barrel Hourly Rate + Materials
-
Cut and Crown Barrel $130
-
Install Pre-Threaded and Chambered Barrel $130
Not including polishing and bluing
-
Install Spring Hourly Rate
-
Install Muzzle Brake (Threaded Barrel) $65
-
Install Barrel and Swivel Hourly Rate
Safeties Installation
-
Dakota, Gentry, Mod 70 Type Safety With Shroud $175
-
Mark II / Beuhlertype $100
-
Chapman Swing Safety Lever $135
Triggers (Installation / Adjustment)
-
Shilen, Timney, Dayton-Traister, Moyer Type $90
-
Double Set $250
-
Single Set $140
Handgun Work
-
Chamfer Revolver Barrel $45
-
Chamfer Revolver Cylinder $80
-
Revolver Action Job $160
Clean, smooth action, not including replacement of parts
-
Rebarrel Revolver $160
Remove old barrel, replace with new factory barrel, labor only
-
Straighten Crane On Revolver $80
-
Install Crane On Revolver $80
-
Install Crane Lock $50
-
Remove / Modify Revolver Hammer Spur $80
-
Convert Revolver From Square To Round Butt $120
-
Semi-Auto Pistol Action Job $220
Clean, smooth action, not including any parts
-
Tighten Slide of 1911 Auto $175
-
Fit Barrel To 1911 Semi-Auto (Non-Ramped) $150
Not Including Barrel
-
Fit Barrel To 1911 Semi-Auto (Ramped) $175
Not Including Barrel
-
Fit & Install Barrel Bushing On 1911 Semi-Auto $120
Does not include cost of bushing
-
Bevel Magazinewell of 1911 Semi-Auto $80
-
Open & Modify Ejection Port Of 1911 Slide $120
-
Throat, Polish Barrel & Feed Ramp Of 1911 $100
-
Fit New Trigger To 1911 $80
Does not include cost of trigger
-
Fit New Hammer to 1911 $100
Does not include cost of hammer
-
Install Fiber Optic Front Sight $45
Existing dovetail w/o cost of sight
-
Install Rear Sight $45
Existing dovetail w/o cost of sight
-
Dehorn & Break Edges For Carry $75
Does not include re-finish
-
Install Semi-Auto Compensator $250
AR-15/10 Work
Does not include cost of parts.
-
Maintenance Cleaning $65
Includes complete disassembly, clean, safety check, oil, and reassemble
-
Maintenance Rebuild $150
Includes new spring & new gas rings added to the maintenance cleaning
-
Install Aftermarket Trigger $80
-
Install Aftermarket Forend / Free-Float $130
-
Assemble Complete Upper $85
-
Assemble Complete Lower $85
-
Assemble Complete Rifle $150
-
Install Flash Hider On Pre-Threaded Barrel $35
-
Install Or Replace Gas Block $65
-
Install Or Replace AR Barrel $80
-
Install Or Replace Butt Stock & Buffer Tube $35
